• Call Processing with Anritsu Instrument Default Settings • Preset 3GPP TS 34.108 Test Parameter Settings
• Confirmed Support for Popular Smartphones
Leaflet
pdf 1.5 MB
2/22/2023
The Radio Communication Analyzer MT8820C platform covers a frequency range of 30 MHz to 2.7 GHz (3.4 GHz to 3.8 GHz). When the dedicated optional measurement software and hardware is installed, the major Tx and Rx characteristics of LTE, LTAdvanced, W-CDMA/HSPA/HSPA Evolution/DC-HSPA/4C-HSDPA, GSM/GPRS/EGPRS, Rev. A, PHS/Advanced PHS, and TD-SCDMA/HSPA/HSDPA Evolution terminals can be measured using a single MT8820C unit.
Brochure
pdf 2.2 MB
8/21/2020
The Radio Communication Analyzer MT8820C is the all-in-one test platform for R&D and manufacturing of LTE/2G/3G UE (User Equipment). It supports manufacturing of LTE terminals, including RF calibration, RF parametric testing, and functional tests.
Product Introduction
pdf 2.5 MB
7/28/2020
All-in-One MT8820C supporting all test functions, including signaling, is the ideal RF tester for RF R&D and manufacturing of TD-LTE/TD-SCDMA/GSM mobile terminals . It gives you cost-benefit, small footprint, and efficient work over other solutions like two boxes.
Product Introduction
pdf 2.0 MB
7/28/2020
The precautions of the interference caused from poor isolation outside MT8820B/C, i.e. between UEs and RF cables, should be considered, Especially, in case of using MT8820B/C Parallel Phone Measurement (PPM) configuration which can do 2port-measurement independently by single unit, the interference problem may be occurred easier than 1 port/1 unit configuration since the UEs and/or RF cables tend to be located closely in the production line. Moreover TDD (Time Division Duplex) mode in TD-SCDMA, and TD-LTE technology tend to have the interference problem since TDD uses the same up and down frequencies. But there is also a possibility that FDD mode in WCDMA, GSM, and LTE FDD while the same frequency in a test is used between UEs. Meanwhile the MT8820C internal isolation between Phone 1 and Phone 2 is at least 138 dB min, which is enough against the interference.
Application Note
pdf 334.3 KB
7/28/2020
The W-CDMA Measurement Software MX882000C is designed for measuring the transmitter and receiver of 3G W-CDMA terminals.
Brochure
pdf 3.1 MB
7/13/2020
The GSM Measurement Software MX882001C supports measurement of transmitters and receivers of digital mobile terminals conforming to GSM/GPRS/EGPRS-the world's most widely used digital mobile standard.
Brochure
pdf 2.7 MB
7/13/2020
The Radio Communication Analyzer MT8820C with TD-SCDMA Measurement Software MX882007C offer powerful support for the R&D and manufacturing phases of 3G TD-SCDMA mobile terminals (1.28 Mcps TDD) now making good market progress mainly in China.
Brochure
pdf 1.8 MB
7/13/2020
The LTE FDD Measurement Software MX882012C/LTE TDD Measurement Software MX882013C is designed for measuring the transmitter and receiver of 3.9G LTE FDD/TDD terminals. The LTE FDD Measurement Software Lite MX882042C, LTE TDD Measurement Software Lite MX882043C is designed for measuring the transmitter and receiver of 3.9G
LTE FDD/TDD terminals.
Brochure
pdf 1.8 MB
7/13/2020
The PHS Measurement Software MX882005C supports transmitter and receiver measurements of PHS mobile terminals now spreading worldwide centered on Asia, including Japan. Installing the PHS Measurement SoftwareMX882005C in one MT8820C main frame supports evaluation of major transmitter and receiver characteristics of PHS terminals and base stations.
Brochure
pdf 2.3 MB
7/13/2020
Leaflet of MT8820C the all-in-one test platform for LTE-Advanced, LTE, 3G and 2G User Equipment.
Leaflet
pdf 1.4 MB
7/13/2020
The LTE FDD Measurement Software MX882012C / the LTE TDD Measurement Software MX882013C is designed for measuring the transmitter and receiver of 3.9G LTE FDD/TDD and LTE-Advanced FDD/TDD terminals.
Product Introduction
pdf 988.7 KB
12/25/2014
