Press the Hard key [Output Level] while in the Parameter window to display entry window. Using the number key pad, input the output level desired.When completed , press the [dBm] key to set up the output level. For the frequency setting, press the blue [Shift] key and the press the [Input Freq] key and then enter the value desired followed by the appropraite frequency key..
Even if the MT8820A does not connect with a terminal, it can measure power. In the Fundamental Measurement screen, the parameter "Power Measurement" is should be set to "On", and by pushing the Single key you can get a power reading on the unit.
Push the [STD] Hard key. This displays the loaded measurement software. To change to GSM, push the soft key for the measurment system desired, in this case GSM. If GSM is not seen, you will need to verify that the system is available and loaded. Please consult the operation manual for more information.
The USIM card is used for the loop-back-test by using it as substitution of SIM card which is actually installed in to W-CDMA terminal.
Yes, 900MHz band is available. The GSM software covers all of the following bands: PCS1900, DCS1800, 900, 850.
On the Parameter screen, press the [Audio] key. If the option"Handset" is available in the [AF] of Audio Input/Output, the option is installed. There should also be a sticker on the outside of the unit on the rear panel that shows that the option is installed.
On the screen for setting parameter, open the window of TCH Test Pattern in common pattern. And Set "Echo". In case of the test by using handset, TCH Test pattern should be set to "Voice Codec" after the parameter of Codec has been set to [EFS].
Pressing the [STD] key. The software which has been installed is displayed on Function menu screen. Select the software you want by pressing the soft key for the software desired to load the software.
Begin by pressing the Config hard key. Then select the RF Output-1 key. This will open a window where Main or Aux can be selected.
In the Common Parameter section of the Parameter screen, if "Packet" exists as a selection in the list of Channel Codings of the Signal, it is installed.
The software for updating is provided on a CD-ROM.Copy the contents of the CD-ROM to a PCMCIA memory card (supplied with the MT8820A) on your PC. Then follow the directions to install the software into the MT8820A via the memory card. Please refer to the instruction manual which is supplied together with the CD-ROM. If there are any questions, please contact Anritsu at 1-800-ANRITSU.
Since it is an echo back examination in a voice cuff examination, no options are required of a terminal. In an opposite examination with a hand set, it is required.
The MX882000A software contains the MX882051A sceanrio. In the MX882000B software the MX882051A scenario is not included and must be purchased separately. In the MX882000B software, other scenarios such as MX882050A/ 53A/54A can be selected. For more information the scenarios, please contact Anritsu.
Once you've turned the screen off remotely, there is no method using the front panel to cancel the screen-off and turn the screen back on. Only a GP-IB command [DISPL] can turn the screen back on again, or you must power cycle the system.
The call processing port provides an input for a BER measurement signal and an output of demodulated signal. The MN8110A I/O adaptor(sold separately) can enable you to change to a BNC connector.
The following options and software are required.1. Option01 W-CDMA Measurement Hardware of MT8820A.2. Option11 Audio Board of MT8820A.3.MX882000B W-CDMA Measurement software.4. Option01 W-CDMA Voice Codec of MX882000B. This combination brings end-to-end communication tests by using a handset and also brings Tx/Rx Audio measurement under a call connection.
The following options and software are required.1.Option02 TDMA Measurement Hardware of MT8820A.2.Option11 Audio Board of MT8820A.3.MX882001A GSM Measurement software.4.Option01 W-CDMA Voice Codec of MX882001A. This combination brings end-to-end communication tests by using a handset and also brings Tx/Rx Audio measurement under a call connection.
Option31 Audio Board retrofit of MT8820A is required. The installation is carried out at Anritsu service site.
The following configuration is required.1. Option01 W-CDMA Measurement Hardwasre of MT8820A.2.MX882000B W-CDMA Measurement Software.3. MX882051A W-CDMA Call Processing Software.4. MX882071A W-CDMA Ciphering SoftwareThis configuration enables the connection test of the communication with the cipher.
The following configuration is required.1. Option01 W-CDMA Measurement Hardware of MT8820A.2. MX882000B W-CDMA Measurement Software.3.MX882051A W-CDMA Call Processing Software