Signal Analyzer MS2840A-040/041 has been developed for R&D and manufacturing of wireless equipment and devices. It has standard spectrum analyzer functions and covers a measurement frequency range from 9 kHz to 3.6 GHz/6 GHz. The close-in SSB phase noise performance is best-of-class for current middle range models and the figures are equal to the high-grade models (–123 dBc/Hz at 1 GHz measurement frequency and 10 kHz offset frequency). Additionally, dedicated options for MS2840A-040/041 greatly enhance their performance to exceed that of other makers’ high-grade models (–133 dBc/Hz at measurement frequency of 500 MHz and offset frequency of 10 kHz). The standard built-in signal analyzer function supports instantaneous monitoring of spectrums, as well as various measurements, including Frequency vs. Time, Phase vs. Time, spectrogram displays, etc. Adding vector modulation analysis software, analog measurement software, vector/analog signal generator options support evaluation of various digital and analog wireless equipment/devices and also adds functions for measuring amplifier noise figure (NF) values.
摺頁冊
pdf 5.3 MB
2026/8/27
This case study highlights how a C/X-band radar system manufacturer improved production and maintenance testing using the Signal Analyzer MS2840A.
案例研究
pdf 480.1 KB
2026/8/18
This operation manual describes the functions of the IQproducerTM, except for the signal generation application.
作業手冊
pdf 4.6 MB
Version: 15
2026/6/24
This describes basic operations and functions of the Multi-carrier IQproducerTM.
作業手冊
pdf 2.0 MB
Version: 10
2026/6/24
This describes basic operations and functions of the TDMA IQproducer.
作業手冊
pdf 2.7 MB
Version: 15
2026/6/24
This is the brochure for the measurement software supported by Signal Analyzer MS269xA, MS2850A, MS2840A and MS2830A.
摺頁冊
pdf 5.9 MB
2026/4/28
The External Mixer Connection Function MX284090A software option facilitates use of Eravant/VDI external mixers recommended by Anritsu. The measurable frequency range is extended by installing this software in the signal analyzers MS2830A/MS2840A/MS2850A when connecting the analyzers to these external mixers.
產品介紹
pdf 1.6 MB
2026/4/28
The External Mixer Connection Function MX284090A is a software option supporting our company's recommended external mixers.
Installing this software in our Signal Analyzers MS2830A/MS2840A/MS2850A and connecting to our recommended external mixer extends
the measurable frequency range. This note explains the configuration and features for V-band evaluation when the MX284090A is installed.
傳單
pdf 390.2 KB
2026/4/28
This document introduces the features, configuration, and expandable frequency range of the Extended Frequency Measurement Solution combining the Signal Analyzer MS2830A/MS2840A/MS2850A with the External Mixer Connection Function MX284090A and Eravant/VDI mixers.
傳單
pdf 313.1 KB
2026/4/28
This leaflet introduces Anritsu’s automotive testing and verification solutions designed to support the development of vehicle electronics.
傳單
pdf 3.4 MB
2026/4/27
Anritsu Electronic Measuring Instruments Catalog Condensed Version (Traditional Chinese)
目錄
pdf 2.9 MB
2026/4/20
This leaflet introduces measurement instruments and components for R&D, production, and monitoring.
產品介紹
pdf 1.8 MB
2026/1/29
Anritsu Electronic Measuring Instruments Catalog Condensed Version
目錄
pdf 6.1 MB
Version: 2025
2026/1/14
This case study introduces solutions for necessary regular test items of pulse radar systems with Signal Analyzer MS2840A and USB Peak Power Sensor MA24418A.
案例研究
pdf 718.3 KB
2025/9/2
This case study introduces solutions for the wideband millimeter-wave radar with combination of a signal analyzer and an external mixer to achieve a maximum image-response-free bandwidth of 7.5 GHz.
案例研究
pdf 683.3 KB
2025/9/2
The MS2830A, MS2840A, MS2850A Signal Analyzer is a spectrum analyzer to
which options such as real-time signal analysis and vector modulation
analysis can be added.
The signal analyzer application (hereinafter “this application”) enables
high-speed and high-accuracy signal processing of wide-ranging analyses
at full-span, a characteristic of conventional sweep-type spectrum
analyzers, using a digital IF block. In addition, the FFT process
(high-speed Fourier conversion) realizes high-speed spectrum analysis
and simultaneous analysis on frequency and time axes not possible with
conventional sweep-type spectrum analyzers. Also, added option enables
recording of the RF input signal as digital data (digitize function). It can
be used in a variety of applications from research and development to
manufacturing thanks to its characteristics.
作業手冊
pdf 10.6 MB
Version: 25
2025/7/30
The phase noise measurement function is provided for measuring phase
noise, which is an important factor for evaluating the short-term stability of
signals. With this application, the MS2690A/MS2691A/MS2692A, MS2830A
, MS2840A or MS2850A can be used in various applications, including design
verification, troubleshooting, and testing on production lines.
作業手冊
pdf 2.9 MB
Version: 14
2025/7/30
This application can be controlled from an external controller (PC) by remote control commands using the MS2690/MS2691/MS2692A,
MS2830A, MS2840A or MS2850A Signal Analyzer(hereinafter, referred to as “this instrument”). The remote control commands are defined by the SCPI format.
作業手冊
pdf 881.2 KB
Version: 12
2025/7/30
Automatic measurement can be performed by using this instrument in
connection with an external controller (PC). This instrument is
standardly equipped with GPIB, Ethernet, and USB interfaces. You can
also select a remote control command from the SCPI mode, which is a
command format defined by the SCPI Consortium, and Native mode,
which is our unique format.
See the MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A Signal
Analyzer Operation Manual (Mainframe Remote Control) for how to
switch the language mode.
You can use the Native mode by converting SCPI commands into Native
ones. See the MS2690A/MS2691A/MS2692A and MS2830A/MS2840A
Signal Analyzer Operation Manual (Mainframe Remote Control) for
details.
To use the Signal Analyzer function on the MS2830A or MS2840A,
Analysis Bandwidth 10 MHz Option or greater is required.
作業手冊
pdf 3.0 MB
Version: 38
2025/7/30
Automatic measurement can be performed by using this instrument in connection with an external controller (PC). This instrument is standard equipped with GPIB, Ethernet, and USB interfaces. You can also select a remote control command from the SCPI mode, which is a command format defined by the SCPI Consortium, and Native mode, which is our unique format.
See the MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A Signal Analyzer Operation Manual (Mainframe Remote Control) for how to switch the language mode.
You can use the Native mode by converting SCPI commands into Native ones. See the MS2690A/MS2691A/MS2692A and MS2830A/MS2840A/MS2850A Signal Analyzer Operation Manual (Mainframe Remote Control) for details.
作業手冊
pdf 4.4 MB
Version: 60
2025/7/30
