下载中心

ESD Protection Adapter J1678A, J1679A

The Protection Adapters J1678A and J1679A are for protecting DUTs and measuring instruments against ESD/EOS and support high-reliability measurements.

BERTWave Series Remote Control Operation Manual

BERTWave Series Remote Control Operation Manual

Selecting Tools at Measurement of High-Speed Digital Signals

The recent rapid increases in data volumes at network equipment, servers, and storage due to increasing use of smartphones, cloud computing, FTTx rollout, video streaming, etc., seem likely to increase even further in future. To cope with demand, many appliances and facilities are using digital signals exceeding the Gbit/s band. Dealing with these high-speed signals requires paying attention not only to the digital aspects but also to analog-type behavior, and care is required in choosing tools for monitoring these signals. This document discusses the key points when handling digital signals exceeding 10 Gbit/s from the perspective of measurement tools.

MP210xA/MP2100B/MP2110A Security Update against WannaCrypt Ransomware Installation Instructions

MP2100A/MP2101A/MP2102A BERTWave Operation Manual

MP2100A/MP2101A/MP2102A BERTWave Operation Manual

MX210001A Jitter Analysis Software Operation Manual

MX210001A Jitter Analysis Software Operation Manual

MX210002A Transmission Analysis Software Operation Manual

MX210002A Transmission Analysis Software Operation Manual

Jitter Analysis Software MX210001A / Transmission Analysis Software MX210002A

All-in-One Simultaneous Waveform Simulation, Jitter Analysis, Eye Pattern Measurement and Eye Mask Test

Procedure for Calculating Extinction Ratio Correction Factor

This document explains how to measure the extinction ratio using sampling oscilloscopes; it is necessary because the measured value must be synchronized with the measuring instrument acting as the reference. The measurement method, Correction Factor calculation and input procedure are described using the MP2100A BERTWave as an example.

理想的远程序列

本书将介绍充分发挥MP2100A性能和速度的标准远程序列。使用本书中所记述的远程序列可从装载于MP2100A的远程指令中选择适合光模块生产的指令，从而构筑更加便捷的光模块测试系统。

MP2100A BERTWave Series - Brochure

The all-in-one MP2100A BERTWave series supporting simultaneous BER and eye-pattern measurements is ideal for both R&D and manufacturing tests because it increases efficiency and cuts measurement costs by eliminating time consuming setup.

MP2100A BERTWave Series - Product Introduction

Product Introduction for the MP2100A BERTWave Series

125 M to 12.5 Gbit/s BERT (MP2100A/MP2101A-090 PPG/ED Bit Rate Extension for PPG/ED)

The MP2100A BERTWave is a new-concept measuring instrument. Simultaneous BER and EYE/Pulse Scope measurements using an all-in-one tester increase efficiency and cut measurement costs by eliminating time-consuming setup. The MP2100A BERTWave series with excellent cost performance is ideal for both R&D and manufacturing tests.

156 M to 11.3 Gbit/s Bessel LPFs for EYE Mask Testing (MP2100A/MP2102A-061 to 085 Low Pass Filter Options)

The MP2100A BERTWave is a new-concept measuring instrument. Simultaneous BER and EYE/Pulse Scope measurements using this all-in-one tester increase efficiency and cut measurement costs by eliminating time-consuming setup. The MP2100A BERTWave series with excellent cost-performance is ideal for both R&D and manufacturing tests.

Ideal for LTE CPRI v4.1 Optical Module Evaluation

Simultaneous BER measurements, Eye/Pulse analysis and Jitter analysis using BERTWave increase efficiency and cut measurement time by eliminating time consuming setup. Fully supported LTE CPRI v4.1 bit rates (6.14G, 4.92G, 3.07G, 2.46G, 1.23 Gbit/s) make the BERTWave ideal for LTE CPRI optical transceiver mobile evaluation.

J1512A 7.5 GHz Passive Probe Set

Ideal probe for GHz-band sampling oscilloscope, Choice of 10:1 or 20:1 attenuation ratio, Low capacity input ideal for monitoring high-speed signal waveforms, Short input ground lead ideal for high-frequency circuit evaluation

External CDR Board for Eye Pattern Measurement (G0301A External CDR Board (<2.667G))

Wide 2000-kHz (max.) loop bandwidth supporting OC-48 measurements in full compliance with ITU-T G.984 for reduced jitter components at waveform monitoring.

For 10G-Band Optical Module Eye Mask

MP2100A-007 Single-Channel Electrical BERT, Optical/Single-Ended Electrical Scope, MP2100A-086/MP2102A-086 LPF (H) for Multi 10G

MP2100A BERTWave-中文产品手册

Using the Eye Pattern to Troubleshoot Signal Impairments

The eye pattern is a useful tool for assessing the integrity of digital signals. The ones and zeroes of a data stream are superimposed to form an eye pattern, providing a good representation of how the data has been affected by a transmission link. Statistical measurements such as extinction ratio and Q-factor are often performed on the eye pattern for compliance testing of devices and transmission paths. These provide good pass/fail criteria, but lend little information as to what may be degrading the signal path.