Overview of RF and Microwave instruments available to meet a variety of solutions. Featuring the frequency range, measurements, and other key features. P/N: 11410-00800
Anritsu offers a comprehensive range of power meters. The ML2490A series has the performance required for narrow fast rising-edge pulse power measurements (e.g., radar). The ML2430A series of power meters are designed for CW applications, offering a combination of accuracy, speed and flexibility in a low cost package. With seven different families of power sensors, including USB sensors to choose from, you can trust you'll find the right combination for precision power measurement, whatever your application. P/N: 11410-00408
This guide provides important notices, warranty, safety, and regulatory compliance information for the Anritsu Power Meters, Power Master™, USB Power Sensors, Thermal Sensors, and Diode Sensors. Be sure to
read these important notices before operating the equipment. P/N: 10100-00066
Download this solution card for an overview of the Power Sensors and Meters available from Anritsu. P/N: 11410-00558
Offering a comprehensive range of power meters. The ML2490A series has the performance required for narrow fast rising-edge pulse power measurements such as radar. The ML2430A series of power meters are designed for CW applications, offering a combination of accuracy, speed, and flexibility in a low cost package. P/N: 11410-00652
The ML2490A series has the performance required for narrow, fast rising-edge pulse power measurements (for example, radar), while the ML2480B series is suited for wideband power measurements on signals such as W-CDMA, WiMAX, LTE, and WLAN. The ML2430A series of power meters are designed for CW applications, offering a combination of accuracy, speed and flexibility in a low cost package. P/N: 11410-00423
This manual provides set-up and operational information for the ML2487B / ML2488B and
ML2495A / ML2496A Peak Power Meters.
This manual provides an overview to the PowerMax software (MX249001A) for use with the
ML248xB and ML249xA power meters. No prior knowledge of PowerMax is assumed, although a
familiarity with the purpose and operation of the ML248xB and ML249xA models is required.
This manual provides descriptions and specifications for Anritsu Power Sensors that are used in conjunction with Anritsu power meters. It includes care, handling and performance verification information. P/N: 10585-00004
This manual provides general information, performance verification, calibration, theory, and service information for the Anritsu Power Meters (ML2487/8A, ML2487/8B and ML2495/6A).
This user guide provides instructions on how to install firmware updates on the ML2400 Series Power Meters using the Anritsu Bootloader Software Utility.
Anritsu bootloader software utility
Bootloader cable (Anritsu part number B41323 – a 9 pin female to 9 pin female RS-232 cable, with TX & RX swapped, CTS & RTS swapped, and DTR & DSR swapped)
Anritsu ML2400 series power meter (ML2437A, ML2438A, ML2487A/B, ML2488A/B, ML2495A, or ML2496A)
The associated new firmware files
Intel-based PC with a Pentium or equivalent processor and the Microsoft® Windows® 2000, Windows XP, or the Windows 7 operating system (32- or 64-bit)
Both the Anritsu Bootloader software utility and power meter firmware can be downloaded from www.anritsu.com. These files will be under the Library tab on the associated product page under the Drivers, Software Downloads heading.
This application note describes a process for simulating radar signals using an Anritsu MG3690C Series Microwave Signal Generator, an ML2490A Series Power Meter and MA2411B Power Sensor, and Anritsu PowerMax Software.
This manual provides detailed information of the GPIB mnemonics for the ML2487B / ML2488B and ML2495A / ML2496A Peak Power Meters. Explanations in this manual apply equally to all units mentioned above unless otherwise stated.
The Rack Mount Kit MT8852B can be ordered with rack mounting hardware that allows it to be mounted into a standard 48 cm equipment rack. P/N: 10585-00025