A small 2 page flyer to showcase the right tools needed to achieve best in class network reliability. P/N: 11410-00855
Leaflet
pdf 1.7 MB
Version: F
29/07/2019
Discover Anritsu's best-in-class tools which will help your technicians and engineers optimize all areas of your network and elevate your network reliability to best-in-class. P/N: 11410-00617
Brochure
pdf 1.6 MB
Version: F
16/07/2019
Transport, Optical & RF Testing for all Elements of the C-RAN Network.
Anritsu has a long history of testing all aspects of the C-RAN. Our instruments evolve to meet the new challenges of testing the C-RAN
networks being rolled out today. Put our experience to work for you!
Brochure
pdf 3.2 MB
Version: B
29/03/2018
The purpose of an in-building wireless (IBW) system is to provide enhanced network coverage
and/or capacity when the existing macro network is not able to adequately service the
demand. Coverage may be poor due to high penetration losses caused by the building
structure or due to low emissivity glass installed to improve the thermal performance of the building. In dense urban environments, adjacent buildings may create an RF barrier that blocks coverage from nearby macro sites. Tall buildings typically have poor coverage on
upper floors since macro site antennas, many floors below, are specifically designed to
suppress energy radiating above the horizon. Capacity may be an issue in venues such as
stadiums, coliseums and convention centers where many thousands of users may be trying to
simultaneously access the network.
Application Note
pdf 1.8 MB
Version: C
28/03/2018
Technicians maintaining diverse systems are forced to carry a large variety of test equipment on-site, including OTDRs, Light Sources, Optical Power Meters, Visible Light Sources, etc., as well as a notebook computer for evaluating the FTTx QoS. On the other hand, fiber construction requires measuring instruments with different functions and performance.In addition, core and backbone networks utilize long fibers while optical access networks use short fibers, both requiring different types of measuring instruments with different performance.But now Anritsu's new line of MT9083 ACCESS Master OTDRs solves all these problems by providing all the measurement functions and performance required for optical fiber construction and maintenance in a compact, lightweight, all-in-one unit that eliminates the burden of carrying many different test sets and instruments on-site.
Brochure
pdf 2.1 MB
15/02/2018
The MX900030A Connector Master is the software to observe, analyze, and make a pass-fail judgment of the fiber optic connector endface by personal computer using the G0306A Video Inspection Probe.
Operations Manual
pdf 647.3 KB
Version: Fourth
01/06/2017
After ruling out traditional problems like passive intermodulation (PIM), poorly aimed antennas and/or other
coaxial problems, dirty fiber connectors account for 60 to 75% of the alarms, failures, and poor throughput
problems found in modern cellular systems today.
Application Note
pdf 2.4 MB
Version: A
13/12/2016
The remote control function sends commands via the communications interface from the remote control PC to set the measuring instrument and read the measurement results and measuring instrument conditions.
Operations Manual
pdf 1.2 MB
Version: 4th
30/09/2016
The MT9083 Series ACCESS Master Optical Time Domain Reflectometer (OTDR) reduces the time to install, commission and maintain fiber spans via high performance hardware and easy-to-use software.
Operations Manual
pdf 8.1 MB
Version: 20th
30/09/2016
Scratches and stains to optic fiber ferrule endfaces are often said to have a negative impact on transmission quality.
The Video Inspection Probe G0306B can be connected to the Network Master MT1000A/MT1100A Series,
the ACCESS Master MT9083x2 Series, uOTDR MT9090A Series product and PC, to show the state of a ferrule endface.
This function is effective for determining whether a ferrule endface is clean, and whether connector replacement is necessary due to connector scratches.
Leaflet
pdf 1.1 MB
15/04/2016
Scratches and stains to optic fiber ferrule endfaces are often said to have a negative impact on transmission quality.
The Video Inspection Probe G0306B can be connected to the Network Master MT1000A/MT1100A Series,
the ACCESS Master MT9083x2 Series, uOTDR MT9090A Series product and PC, to show the state of a ferrule endface.
This function is effective for determining whether a ferrule endface is clean, and whether connector replacement is necessary due to connector scratches.
Product Introduction
pdf 1.7 MB
15/04/2016
DAS can encompass Fiber Optic Cables, RF Cables, Fiber Optic (PON) Splitters, RF Splitters, Radiating Cables, Amplifiers and all of these components can be in one
single system. Each system will be as unique as the facility to which it will be installed. There is no simple "one size fits all"
solution to testing a DAS, but if you break it down, it can be effectively tested and troubleshot. This application note breaks down these various types of components. P/N: 11410-00887
Application Note
pdf 4.9 MB
Version: A
02/11/2015
"Fiber Visualizer" is a new fault location function designed to simplify the entire testing process. Fiber Visualizer automatically selects the testing parameters to ensure the correct setup and provides a simple, graphical summary of the fiber under test within seconds. A comprehensive PDF report can then be customized and generated, completing the testing process. Recent enhancements provide better event detection and accuracy as well as individualized PASS/FAIL analysis to simplify your FTTx/PON testing.
Leaflet
pdf 386.6 KB
09/04/2015
Scratches and stains to optic fiber ferrule endfaces are often said to have a negative impact on transmission quality.
The Video Inspection Probe G0306A can be connected to the Network Master MT1000A/MT1100A Series,
the ACCESS Master MT9083x2 Series, uOTDR MT9090A Series product and PC, to show the state of a ferrule endface.
This function is effective for determining whether a ferrule endface is clean, and whether connector replacement is necessary due to connector scratches.
Product Introduction
pdf 1.4 MB
28/05/2014
Scratches and stains to optic fiber ferrule endfaces are often said to have a negative impact on transmission quality.
The OPTION-545VIP can be connected to an MT908x Series ACCESS Master, MT9090A Network Master Series product and PC, to show the state of a ferrule endface.
This function is effective for determining whether a ferrule endface is clean, and whether connector replacement is necessary due to connector scratches.
Product Introduction
pdf 1.5 MB
24/03/2014
According to increasing the data traffic, the PON network is developing continuously and it has been progressing toward 10G-PON/10GE-PON network. Therefore, the loss and the ORL measurement of OTDRs will be more important not only 1310/1550 nm testing but also 1490 nm testing, as used for the downstream. In addition, The CWDM is deployed for secure networks and the OTDR measurement is also required for this network.
Anritsu will add 1490 nm wavelength models to the ACCESS MasterTM series. We will offer the additional solution for various optical I&M works, the tri-band wavelength (1310/1490/1550 nm) for use FTTx/PON network applications and quad-band wavelength (1310/1490/1550/1625 nm) model for FTTx/PON full I&M work and CWDM network application.
Leaflet
pdf 178.3 KB
17/06/2013
“Fiber Visualizer” is a new fault location function designed to simplify the entire testing process. Fiber Visualizer automatically selects the testing parameters to ensure the correct setup and provides a simple graphical summary of the fiber under test within seconds. A comprehensive PDF report can then be customized and generated, completing the testing process.
Leaflet
pdf 508.8 KB
28/05/2013
The MX900021A screen display software is software to display the MT9083 Series ACCESS Master screens to a personal computer via USB.
Operations Manual
pdf 1.6 MB
23/04/2013
Anritsu is now pleased to announce the enhanced MT9083A2/MT9083B2/MT9083C2 models. The ACCESS Master MT9083x2 now features a 7-inch widescreen TFT-LCD display for use both indoors and outdoors, enhanced battery operation time (up to 12 hours), increased operating temperature range (-10 to 50 oC) and new short-cut function keys.
Leaflet
pdf 283.8 KB
24/08/2012
ProductsMobile Wireless Communications
