Skip to main content

All-in-One PCIe Gen1 to Gen5 Support

Anritsu MP1900A, Certified for PCIe Gen3/4, USB3.2 and Thunderbolt 3, PCIe Gen5 Base/CEM Compliance Test Ready

The spread of IoT devices and Cloud Computing services is causing explosive growth in data traffic handled by digital devices, in turn requiring faster serial device interfaces. The PCIe and USB interfaces used by digital devices are handling ever larger data volumes so the resulting next-generation PCI Express Gen5 standard reaches higher speeds of 32 GT/s, while USB3.1 Gen 2 supports 10 Gbit/s, USB4 supports 20 Gbit/s and USB4 Type-C is also compatible with Thunderbolt which also supports 20 Gbit/s.

The MP1900A is an all-in-one BERT solution for debugging and compliance tests of high-speed buses, and also supports PCIe, USB, and Thunderbolt3 receiver tests.

  • The MP1900A is an industry-first all-in-one solution for PCIe Gen1 to Gen5 compliance tests.
  • The MP1900A has been approved by standards organizations for PCIe Gen3/4, USB3.2, and Thunderbolt3 compliance tests.
  • Software for automating complex compliance tests supports oscilloscopes from key makers.
Target Applications
MP1900A Supported Interfaces

PCIe, USB, and Thunderbolt Receiver Test Solution

The Signal Quality Analyzer-R MP1900A supports measurement requirements from the first development stages for high-speed, next-generation, digital interface standards (CEI-28G/56G/112G, InfiniBand, 100G/400G/800G Ethernet, Fibre Channel, Thunderbolt 3, PCI Express (PCIe), USB) using 32-Gbit/s PPG and ED modules, Jitter/Noise addition functions, and application software.

Multi-interface Support using Wideband MP1900A BERT

Typical Compliance Test Solution

PCIe Gen3/4/5 Base Specification Receiver Test

PCI Express Gen5 Base Specification Receiver Test

PCIe Gen3/4/5 CEM Specification Receiver Test

PCI Express Device Evaluation Setup

USB 3.2 Gen1/2 Receiver Test

USB Device Evaluation Setup

USB Type-C Receiver Test (USB4, Thunderbolt3)

Thunderbolt Receiver Test Solution
arrow-to-top

Automation software supporting oscilloscopes from key makers

Automation software for automating Rx tests of high-speed serial bus interfaces controls the MP1900A (PPG/ED, noise signal source, variable ISI channel) and real-time oscilloscope to automate calibration of signals required for complex operations, Jitter Tolerance tests, and creation of ports. The high-reproducibility, easy measurements greatly reduce the work load of test engineers.

Real-time oscilloscopes from the main makers can be used in combination with the MP1900A to calibrate test signals, helping cut capital investment costs by making efficient use of owned assets.

Connection of Oscilloscope
Automation testing

Refer to the Selection Guide (MP1900A-E-Z-1) for the supported combination of real-time oscilloscopes and automation software.

arrow-to-top

Versatilel debugging functions

Link Training Function

The PCIe and USB receiver test requires establishment of the Link status before performing the DUT BER test.
Installing the Link Training option in the MP1900A supports verification of the Link status required for measurement. Additionally, the PCIe Link Training option has an LTSSM Analysis function for troubleshooting problems the Link status cannot be configured.

PCIe Link Training and LTSSM Analysis Function (MX183000A-PL021, PL025)

  • Protocol aware, all-in-one, PCI Express Gen 1 to 5 Receiver Test
  • Link Training and LTSSM Analysis functions
Anritsu MP1900A BERT Link Training
Supports physical layer measurements of add-in cards and system boards
  • Tx/Rx Link Equalization Response Test
  • Rx Link Equalization Test
  • Receiver Jitter Tolerance Test
Link Training State transitions
Link Training State transitions
LTSSM Log
LTSSM Log

USB Link Training (MX183000A-PL022)

  • Protocol aware, all-in-one, USB3.1 Rx test solution
  • Link Training and LTSSM Analysis
Controls transition to Loopback (Link Training function)
Controls transition to Loopback (Link Training function)
Supports Link troubleshooting (LTSSM Analysis function)
Supports Link troubleshooting (LTSSM Analysis function)

Matrix Scan Function

To secure high-quality communications with the Link partner, the best combination of the Tx-side EQ and Rx-side EQ must be selected.
The Matrix scan function scans for the best Tx EQ setting at the receiver to find the best setting automatically at the receiver.

Matrix Scan Function

Jitter Tolerance Test Function (MX183000A-PL001)

MP1900A series offers strong support for receiver stressed input tolerance tests by generating high-quality signals before jitter and noise addition as well as for adding high-linearity jitter and noise.

  • Supports versatile Jitter Tolerance measurements
  • Injects SJ/RJ/BUJ for PHY device Jitter Tolerance tests
  • Supports Mask measurements for various standards
  • Shortens measurement time using low-error-rate (1E-12, 1E-15, etc.) estimation function
  • Uses Binary, Upward, Downward, and Binary + Linear search methods to measure tolerance points dependent on device characteristics
  • Users can customize the Jitter Tolerance test mask.

Low-Rate Estimated BER Measurement
Low-Rate Estimated BER Measurement

arrow-to-top
Confirm your country below to see local events, contact information and special offers.