Offering a comprehensive range of power meters. The ML2490A series has the performance required for narrow fast rising-edge pulse power measurements such as radar, while the ML2480B series is suited for Wideband power measurements on signals such as W-CDMA, LTE, and WLAN. The ML2430A series of power meters are designed for CW applications, offering a combination of accuracy, speed, and flexibility in a low cost package.
This guide provides important notices, warranty, safety, and regulatory compliance information for the Anritsu Power Meters, Power Master™, USB Power Sensors, Thermal Sensors, and Diode Sensors. Be sure to
read these important notices before operating the equipment.
Overview of RF and Microwave instruments available to meet a variety of solutions. Featuring the frequency range, measurements, and other key features.
This manual provides set-up and operational information for the ML2487B / ML2488B and
ML2495A / ML2496A Peak Power Meters.
This manual provides an overview to the PowerMax software (MX249001A) for use with the
ML248xB and ML249xA power meters. No prior knowledge of PowerMax is assumed, although a
familiarity with the purpose and operation of the ML248xB and ML249xA models is required.
The ML2490A series has the performance required for narrow fast rising-edge pulse power measurements (e.g., radar), while the ML2480B series is suited for Wideband power measurements on signals such as W-CDMA, WLAN, and WiMAX. The ML2430A series of power meters are designed for CW applications, offering a combination of accuracy, speed and flexibility in a low cost package.
Also available are seven different families of power sensors with frequency coverage up to 50 GHz and dynamic range up to 90 dB. Most Anritsu power sensors can work in either pulsed/modulated or CW mode (the ML2480B/90A series meters offer both modes). In choosing a power sensor, several factors must be considered, including: frequency range, dynamic range, and the modulation type. The rise time of the sensor should also be chosen to match the rise time of the modulation.
This RF & Microwave Reference Chart provides content on Band Designation, RF Measurements, S Parameters, Electromagnetic Spectrum, Atmospheric Absorption, RF Connectors, Power to Voltage Conversions, Amplitude Modulation, Pulse Modulation, Frequency Modulation, Waveguide Designation, and Adaptor Error Uncertainties.
Anritsu Power Meters and Sensors for Power Measurement Solutions.
Download this solution card for an overview of the Power Sensors and Meters available from Anritsu.
This manual provides general information, performance verification, calibration, theory, and service information for the Anritsu Power Meters (ML2487/8A, ML2487/8B and ML2495/6A).
This user guide provides instructions on how to install firmware updates on the ML2400 Series Power Meters using the Anritsu Bootloader Software Utility.
Anritsu bootloader software utility
Bootloader cable (Anritsu part number B41323 – a 9 pin female to 9 pin female RS-232 cable, with TX & RX swapped, CTS & RTS swapped, and DTR & DSR swapped)
Anritsu ML2400 series power meter (ML2437A, ML2438A, ML2487A/B, ML2488A/B, ML2495A, or ML2496A)
The associated new firmware files
Intel-based PC with a Pentium or equivalent processor and the Microsoft® Windows® 2000, Windows XP, or the Windows 7 operating system (32- or 64-bit)
Both the Anritsu Bootloader software utility and power meter firmware can be downloaded from www.anritsu.com. These files will be under the Library tab on the associated product page under the Drivers, Software Downloads heading.
This application note describes a process for simulating radar signals using an Anritsu MG3690C Series Microwave Signal Generator, an ML2490A Series Power Meter and MA2411B Power Sensor, and Anritsu PowerMax Software.
The ML2490A series has the performance required for narrow fast rising-edge pulse power measurements (e.g. radar). The ML2480B series is suited for wide-band power measurements on signals such as LTE, W-CDMA, WLAN, and WiMAX. The ML2430A series of power meters are designed for CW applications, offering a combination of accuracy, speed and flexibility in a low cost package.
With seven different families of power sensors to choose from, you can trust you’ll find the right combination for precision power measurement, whatever your application.
This manual provides detailed information of the GPIB mnemonics for the ML2487B / ML2488B and ML2495A / ML2496A Peak Power Meters. Explanations in this manual apply equally to all units mentioned above unless otherwise stated.
Rack Mount Kit Installation Guide for the MT8852B, MT8855A, ML243xA,
This file will explain the change history in 2.32 relative to 2.31. Read for more information on the changes.