This guide explains the simple procedure for installing the waveform patterns and
IQproducer license in the Vector Signal Analyzer MG3710A/MG3710E or Analog Signal Generator
MG3740A (with Digital Modulation option).
User Guide
pdf 282.4 KB
21/04/2021
This guide outlines operation procedures for the BER Measurement Function option for the
Vector Signal Generator MG3710A/MG3710E and Analog Signal Generator MG3740A (with Digital
Modulation option).
User Guide
pdf 318.8 KB
21/04/2021
This guide explains how to install firmware in the Vector Signal Generator MG3710A/MG3710E and
Analog Signal Generator MG3740A.
User Guide
pdf 282.7 KB
21/04/2021
This guide explains the Vector Signal Generator MG3710A/MG3710E and Analog Signal Generator MG3740A (with Digital Modulation option) procedures for copying and loading waveform patterns and selecting the signal for output.
User Guide
pdf 385.7 KB
21/04/2021
This guide explains the dual signal combination method using the Combination of
Baseband Signal Function (Opt.048/078) installed in the Vector Signal Generator MG3710A/MG3710E and Analog Signal Generator MG3740A (with Digital Modulation Option).
User Guide
pdf 798.7 KB
21/04/2021
Unlike general-purpose vector signal generators, the MG3710A/MG3710E can generate a combined signal for different wireless systems, such as LTE, W-CDMA, GSM, etc. This application note explains some of the problems when generating signals for combinations of different wireless systems using a general-purpose vector signal generator. It also explains how to solve these problems using the MG3710A/MG3710E and then introduces an example of how to generate Multi-Standard Radio signals.
Application Note
pdf 1.2 MB
21/04/2021
This document introduces the two-signal combine function of the MG3710A/MG3710E Vector Signal Generator and explains an optimized technique for measurement using this function.
Application Note
pdf 1.5 MB
21/04/2021
MX370073B DFS Radar Pattern (hereafter “this waveform pattern”)
contains standard waveform pattern conforming to the TELEC-T403
V12.1 and FCC06-96 (Released: June 30, 2006), FCC13-22 (Released:
February 20, 2013) Dynamic Frequency Selection test.
Downloading this waveform pattern to the MG3710A Vector Signal
Generator (hereafter MG3710A) supports generation of radar pattern
signals used at Rx Dynamic Frequency Selection (DFS) tests.
Use of this waveform pattern requires a license corresponding to the
serial number of the MG3710A using the pattern. When using this
pattern on multiple MG3710A units, a license must be purchased for each
MG3710A unit using this pattern.
Operations Manual
pdf 2.4 MB
Version: 2
28/01/2021
The MG3710A/MG3710E is a vector signal generator that includes an arbitrary
waveform generator. It can be used for a wide range of applications, from
R&D to manufacturing of digital mobile communication systems, devices,
and equipment.
The MG3740A is an analog signal generator. It can be used for a wide
range of applications, from R&D to manufacturing of analog radio base
stations, devices, and equipment.
Operations Manual
pdf 23.0 MB
Version: 19
17/12/2020
This document describes type and size of memory and storage device inside Anritsu Signal Analyzer and Signal Generator
series in order to use safely the products against information security threat.
Leaflet
pdf 119.3 KB
3/11/2020
This document explains how to order the new MG3710E and MG3710E/MG3710A retrofit options and software.
Configuration Guides
pdf 739.1 KB
26/10/2020
The MG3710E is a vector signal generator with 6 GHz upper frequency limit and 120 MHz wide RF modulation baseband generator. It outputs various radio systems signals for cellular communications, such as LTE FDD/TDD, W-CDMA, GSM as well as narrowband communications, such as WLAN, Bluetooth and GPS.
Brochure
pdf 5.6 MB
2/09/2020
Introduces Anritsu 5G solutions and products.
Anritsu will contribute to customer's 5G product development and future innovation of network.
Brochure
pdf 3.1 MB
31/07/2020
The MG3710A is a vector signal generator that includes an arbitrary waveform generator. It can be used for a wide range of applications, from R&D to manufacturing of digital mobile communication systems, devices, and equipment.
The MG3710A has the following features, and one MG3710A can address from the current major mobile communications to the next-generation mobile communications.
Operations Manual
pdf 1.7 MB
Version: 4
9/03/2020
MX370114A/MX269914A 5G NR FDD sub-6GHz IQproducer™ is software used to generate
waveform patterns conforming to the 3GPP 5G NR specifications.
Operations Manual
pdf 1.7 MB
Version: 1
9/03/2020
Parameters for the waveform for the target communication system are set using a GUI to a generate a waveform pattern file for the MG3710A. The embedded Windows application IQproducer saves generated arbitrary waveform pattern files to the internal hard disk and signals are output simply by selecting the waveform pattern. In addition, a user-generated custom IQ sample file in ASCII format created by common Electronic Design Automation (EDA) software such as MATLAB, can be converted into a
custom waveform pattern file for the MG3710A.
Brochure
pdf 6.4 MB
18/02/2020
Each category contains multiple waveform pattern files each with preset parameters for each system. These default waveform patterns are saved on the MG3710A/B hard disk for easy access, but other waveform patterns are supported using the IQproducer waveform generation software.
Brochure
pdf 2.3 MB
18/02/2020
Installing the DFS Radar Patterns option MX370073B/MX370075A in the Vector Signal Generator MG3710E supports output of FCC, ETSI and Japan MIC standards DFS test signals. Output of complex combinations of pulse, chirp and hopping signals required to support DFS tests is made easy just by selecting combination files supplied with the MX370073B/MX370075A.
Leaflet
pdf 944.7 KB
18/11/2019
Installing the DFS Radar Pattern MX370073B option in the Vector Signal Generator MG3710A/MG3710E supports output of FCC and Japan MIC standard DFS test signals.
External PC not required. Simply selecting prepared waveform pattern outputs various signals using MG3710A/MG3710E built-in Sequence function. Offers 5.3-GHz band waveform patterns adopted by Japan MIC standard in July 2019
Product Introduction
pdf 1.1 MB
30/10/2019
Installing the MX370075A DFS (ETSI) Waveform Patterns option in the MG3710A Vector Signal Generator supports output of ETSI EN 301 893 DFS test signals. Output of complex combinations of pulse and chirp signals required to support DFS tests is made easy just by selecting combination files supplied with the MX370075A.
Product Introduction
pdf 882.8 KB
30/10/2019
